Emulex LP1005DC-CM2 Bedienungsanleitung Seite 104
- Seite / 162
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Driver for Linux -Troubleshooting Section Page 98
HBAnyware Security Configurator Situations - Backup Masters
Table 6: HBAnyware Security Configurator - Backup Masters Situtations
Situation Resolution
Cannot create a backup master. Select a system (or group of systems) from the MSC to be
the Backup Master. The system must be either an
unsecured system (which will be secured by being made a
Backup Master), or a system that is not part of any ASG
(client or server). These systems will mirror the MSC's
security configuration.
Because the Backup Master may some day take over as
the MSC, the Backup Master must be able to physically
access all of the systems that the MSC can access.
Therefore, if the MSC is connected to multiple fabrics, the
Backup Master also must be connected to those same
fabrics. When you select a Backup Master, the HBAnyware
Security Configurator displays a warning if it detects that
the system selected to be a Backup Master is not able to
physically access the same systems that the MSC can
access
Cannot modify the Security Configurator.
Select a system (or group of systems) from the MSC to be
the Backup Master. The system must be either an
unsecured system (which will be secured by being made a
Backup Master), or a system that is not part of any ASG
(client or server). These systems will mirror the MSC's
security configuration.
The Backup Master has client access from the HBAnyware
Utility to all of the servers in the MSC's ACG. However, the
Backup Master does not have client access to the MSC and
it cannot modify the security configuration (create, modify or
delete ASGs).
No Backup Master and the MSC Is no longer
available. I do not have a Backup Master and the
MSC system is no longer available. The servers
are still secure. I installed the Security
Configurator on another system, but I cannot
access those servers to remove the security from
them..
The servers are no longer part of a valid security
configuration because there is no MSC to provide master
control of the configuration. In order to reset the security on
the affected servers, you will need to contact Emulex
Technical Support to receive a special application and
instructions on the reset procedure. After the servers have
been reset, they should be seen by the Security
Configurator and the HBAnyware Utility. At this point, you
can set up security again through another MSC. At this
time, also create a Backup Master.
The Backup Master tab is not available. The Backup Master tab is displayed only when the Security
Configurator is running on the MSC or a Backup Master.
You use this tab to set up a system or systems to be
backups to the MSC and to replace the MSC with a Backup
Master.
Each time you start the Security Configurator on the MSC
and there is no Backup Master assigned, a warning
message urges you to assign at least one Backup Master to
prevent the loss of security information if the MSC were to
become disabled.
- Emulex Driver and Utilities 1
- Installation 7
- Compatibility 8
- Known Issues 8
- Installing the Driver Kit 9
- Directory Structure 10
- Upgrading the Kernel 12
- Installing the Utilities 18
- Uninstalling the Utililities 19
- Configuration 20
- Examples of Modifications 21
- The Menu Bar 22
- The Toolbar 22
- The Toolbar Icon Definitions 23
- Sort and Display Icons 23
- The Discovery Tree 24
- Property Tabs 25
- Status Bar 25
- Start lputil 28
- HBA Tasks 29
- Discover HBAs Using lputil 30
- Sort HBA Information 31
- button 32
- Sort Local HBAs Using lputil 32
- View Discovered Elements 32
- View Host Attributes 33
- View Target Attributes 34
- View LUN Attributes 35
- View Fabric Attributes 37
- View General HBA Attributes 37
- Status Area Field Definitions 38
- View Detailed HBA Attributes 39
- View Port Information 40
- Port Field Definitions 41
- View Statistics 42
- View Firmware Information 44
- View Target Mapping 45
- View Driver Parameters 46
- Driver Parameter Tab Buttons 48
- ./stop_hbanyware 48
- Figure 20: The Main Menu 49
- Reset Adapters 50
- Reset the HBA Using lputil 51
- Update Firmware 52
- Prerequisites 53
- Procedure 53
- Update Firmware Using lputil 55
- Boot Code 56
- Load Boot Code using lputil 58
- Configure the Driver 61
- Reset All Default Values 64
- Set Up LUN Support 67
- Understand Device Numbering 68
- Download PCI Configuration 68
- The 'devlabel' Tool 72
- Set Up Persistent Binding 73
- Add Persistent Binding 74
- HBAnyware Security 76
- Access Control Groups 78
- ACG Icons 80
- Create the ACG 80
- Add a Server to the ACG 81
- Delete a Server from the ACG 82
- Generate New Security Keys 84
- Access a Switch 86
- Access Sub-Groups 87
- ASG Icons 88
- Create an ASG 88
- Reserved Indices - Examples 90
- Add a Server to an ASG 90
- Deleting an ASG 91
- Edit an ASG 91
- Backup Masters 93
- Create a Backup Master 95
- Troubleshooting 98
- Disable the rmserver process: 101
- Error Message Situations 105
- Introducton 108
- Message Group Masks 109
- Message Log Example 110
- ELS Events (0100 - 0199) 111
- Mailbox Events (0300 - 0399) 123
- LUN <num> 153
- Link Events (1300 - 1399) 159
- SLI Events (1400 - 1499) 160
Verwandte Produkte und Handbücher für Software Emulex LP1005DC-CM2
Software Emulex LP9802DC Bedienungsanleitung
(69 Seiten)
(69 Seiten)
Software Emulex LP10000ExDC Bedienungsanleitung
(366 Seiten)
(366 Seiten)
Software Emulex LP982 Bedienungsanleitung
(371 Seiten)
(371 Seiten)
Software Emulex LP21000 Bedienungsanleitung
(274 Seiten)
(274 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern