Emulex LP10000ExDC Bedienungsanleitung Seite 22
- Seite / 366
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
❍ lpfc_scan_down can only have 0 or 1 values in 2.01g drivers. If you have a
value other than 0 or 1 for lpfc_scan_down in the prior installation, you
must set lpfc_fcp_bind_method parameter in the 2.01g driver accordingly.
Refer to the parameter description section in the online Configuration
manual for detailed descriptions of the lpfc_fcp_bind_method and
lpfc_scan_down parameters.
❍ lpfc_automap can only have 0 or 1 values in 2.01g drivers. If you have a
value other than 0 or 1 for lpfc_automap in the old installation, you must set
lpfc_fcp_bind_method parameter in the 2.01g driver accordingly. Refer to
the parameter description section in the online Configuration manual for
detailed descriptions of the lpfc_fcp_bind_method and lpfc_automap
parameters.
❍ lpfc_fcpfabric_tmo has been renamed to lpfc_extra_io_tmo.
❍ lpfc_discovery_threads is a new parameter.
❍ lpfc_fdmi_on is a new parameter.
❍ lpfc_nodev_tmo now defaults to 30 seconds instead of 0.
❍ lpfc_num_iocbs now defaults to 256 instead of 1024.
❍ lpfc_num_bufs now defaults to 128 instead of 1024.
❍ lpfc_cr_count now defaults to 1 instead of 0.
5. Build the new driver as described in the appropriate build procedure section of this
manual.
Emulex Documentation, Drivers and Software
22
- Version 2.01g 1
- Table of Contents 1
- Supported Features 2
- New Features in this Release 3
- Known Issues 8
- File Name 9
- Utilities tar File 10
- Utilities RPM File 11
- Running the DOS Utility 12
- Using the UNIX-based Utility 14
- Driver Information 18
- Compatibility 19
- Install the Driver 20
- # cd /usr/src/linux 27
- # make mrproper 27
- # make cloneconfig 27
- # make dep 27
- # mkdir emlxtemp 29
- # cd emlxtemp 29
- # rpm -i <filename.rpm> 29
- # rpm -a -q 29
- # rpm -e <rpm_name> 29
- Build the Driver as a Module 30
- Load the Driver 31
- Build the Kernel and Modules 43
- Channel Boot Disk 48
- Install the Utilities 51
- 3. Type: 52
- Prerequisites 53
- Start HBAnyware for Linux 59
- Use HBAnyware 60
- The Toolbar 61
- The Discovery Tree 62
- Property Tabs 64
- Status Bar 64
- Using the CLI Client 65
- CLI Client Command Reference 65
- Start lputil 68
- Discover HBAs - Introduction 69
- Discover HBAs Using HBAnyware 70
- List Adapters using lputil 71
- Reset Adapter - Introduction 72
- Reset HBAs Using HBAnyware 73
- Reset Adapter 74
- Sort HBAs 77
- Sort by Fabric Address 78
- Sort by Local HBAs Only 78
- View Discovered Elements 79
- View Host Attributes 80
- View Fabric Attributes 81
- View Target Attributes 82
- View LUN Attributes 84
- View General HBA Attributes 86
- Link Status Area 87
- View Detailed HBA Attributes 88
- View Port Attributes 90
- View Port Statistics 92
- ● Assign AL_PA IDs 93
- View Adapter Information 94
- Load Firmware Using HBAnyware 97
- Details tab 98
- Update Firmware 99
- FC Boot 100
- Update x86 BootBIOS 101
- Enable x86 BootBIOS 102
- Update EFIBoot 103
- Boot the EFI System 104
- Configuring the Driver 105
- Reset All Default Values 109
- Configuration Methods 110
- Set Up LUN Support 114
- Configuring IP Networking 116
- Understand Device Numbering 117
- Download PCI Configuration 118
- Enable BootBIOS 128
- To show persistent names: 130
- # devlabel status 130
- View Target Mapping 131
- Set Up Persistent Binding 132
- HBAnyware Security Overview 135
- /usr/sbin/hbanyware/ssc 136
- Create the ACG 137
- 5. Click OK or Apply 138
- Designate an MSC 139
- ACG Icons 141
- Add a Server to the ACG 144
- Delete a Server from the ACG 145
- Generate New Security Keys 148
- Configuration 149
- Access a Switch 150
- ASG Icons 151
- Create an ASG 153
- Reserved Indices - Examples 155
- Add a Server to an ASG 156
- Deleting an ASG 157
- Edit an ASG 159
- About Offline ASGs 161
- Backup Masters - Introduction 162
- Create a Backup Master 164
- FCP Target Mode Events 169
- Miscellaneous Events 169
- Link Events 169
- SLI Events 169
- IOCTL Events 169
- Introduction 170
- Run HBAnyware 172
- Management Server 174
- SAN Management Workstation 175
- Does Not Have 175
- Cannot See New LUNS 176
- All Servers Are Not Displayed 179
- Cannot Add or Remove a Server 180
- Cannot Create a Backup Master 187
- Available 189
- Client Assigned" 194
- Unsecure System" 195
- Master Client System" 196
- Connect to the FC Network 197
- Were Offline 198
- ELS Events (0100 - 0199) 204
- Mailbox Events (0300 - 0399) 242
- ❍ Reduce the LUN size 337
- Link Events (1300 - 1399) 358
- SLI Events (1400 - 1499) 362
Verwandte Produkte und Handbücher für Software Emulex LP10000ExDC
Software Emulex LP982 Bedienungsanleitung
(371 Seiten)
(371 Seiten)
Software Emulex LP21000 Bedienungsanleitung
(274 Seiten)
(274 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern