Emulex LP10000ExDC Bedienungsanleitung Seite 116
- Seite / 366
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Configuring IP Networking
When configuring for IP service you must supply the name of the host machine that Linux should use for a
particular network interface. At installation time, if you indicated that lpfc should provide IP networking
service over Fibre Channel you should set up a /etc/sysconfig/network-scripts/ifcfg-lpfn<0-N> file for each
LightPulse adapter being configured.
By default, "network" is set to O and must be set to 1 prior to building the driver.
Note
Names you specify in these ifcfg-lpfn<0-N> files must have
valid IP addresses associated with them, via NIS or DNS
or whatever hostname-to-IP-address translation scheme
you employ.
Below is an example ifcfg-lpfn<0-N> file:
Note
The file, ifcfg-eth0 can also be used as an example. You
must restart the network interfaces either by rebooting the
machine or by manually typing ifdown lpfn<0-N> and ifup
<0-N> for these changes to take effect.
Emulex Documentation, Drivers and Software
116
- Version 2.01g 1
- Table of Contents 1
- Supported Features 2
- New Features in this Release 3
- Known Issues 8
- File Name 9
- Utilities tar File 10
- Utilities RPM File 11
- Running the DOS Utility 12
- Using the UNIX-based Utility 14
- Driver Information 18
- Compatibility 19
- Install the Driver 20
- # cd /usr/src/linux 27
- # make mrproper 27
- # make cloneconfig 27
- # make dep 27
- # mkdir emlxtemp 29
- # cd emlxtemp 29
- # rpm -i <filename.rpm> 29
- # rpm -a -q 29
- # rpm -e <rpm_name> 29
- Build the Driver as a Module 30
- Load the Driver 31
- Build the Kernel and Modules 43
- Channel Boot Disk 48
- Install the Utilities 51
- 3. Type: 52
- Prerequisites 53
- Start HBAnyware for Linux 59
- Use HBAnyware 60
- The Toolbar 61
- The Discovery Tree 62
- Property Tabs 64
- Status Bar 64
- Using the CLI Client 65
- CLI Client Command Reference 65
- Start lputil 68
- Discover HBAs - Introduction 69
- Discover HBAs Using HBAnyware 70
- List Adapters using lputil 71
- Reset Adapter - Introduction 72
- Reset HBAs Using HBAnyware 73
- Reset Adapter 74
- Sort HBAs 77
- Sort by Fabric Address 78
- Sort by Local HBAs Only 78
- View Discovered Elements 79
- View Host Attributes 80
- View Fabric Attributes 81
- View Target Attributes 82
- View LUN Attributes 84
- View General HBA Attributes 86
- Link Status Area 87
- View Detailed HBA Attributes 88
- View Port Attributes 90
- View Port Statistics 92
- ● Assign AL_PA IDs 93
- View Adapter Information 94
- Load Firmware Using HBAnyware 97
- Details tab 98
- Update Firmware 99
- FC Boot 100
- Update x86 BootBIOS 101
- Enable x86 BootBIOS 102
- Update EFIBoot 103
- Boot the EFI System 104
- Configuring the Driver 105
- Reset All Default Values 109
- Configuration Methods 110
- Set Up LUN Support 114
- Configuring IP Networking 116
- Understand Device Numbering 117
- Download PCI Configuration 118
- Enable BootBIOS 128
- To show persistent names: 130
- # devlabel status 130
- View Target Mapping 131
- Set Up Persistent Binding 132
- HBAnyware Security Overview 135
- /usr/sbin/hbanyware/ssc 136
- Create the ACG 137
- 5. Click OK or Apply 138
- Designate an MSC 139
- ACG Icons 141
- Add a Server to the ACG 144
- Delete a Server from the ACG 145
- Generate New Security Keys 148
- Configuration 149
- Access a Switch 150
- ASG Icons 151
- Create an ASG 153
- Reserved Indices - Examples 155
- Add a Server to an ASG 156
- Deleting an ASG 157
- Edit an ASG 159
- About Offline ASGs 161
- Backup Masters - Introduction 162
- Create a Backup Master 164
- FCP Target Mode Events 169
- Miscellaneous Events 169
- Link Events 169
- SLI Events 169
- IOCTL Events 169
- Introduction 170
- Run HBAnyware 172
- Management Server 174
- SAN Management Workstation 175
- Does Not Have 175
- Cannot See New LUNS 176
- All Servers Are Not Displayed 179
- Cannot Add or Remove a Server 180
- Cannot Create a Backup Master 187
- Available 189
- Client Assigned" 194
- Unsecure System" 195
- Master Client System" 196
- Connect to the FC Network 197
- Were Offline 198
- ELS Events (0100 - 0199) 204
- Mailbox Events (0300 - 0399) 242
- ❍ Reduce the LUN size 337
- Link Events (1300 - 1399) 358
- SLI Events (1400 - 1499) 362
Verwandte Produkte und Handbücher für Software Emulex LP10000ExDC
Software Emulex LP982 Bedienungsanleitung
(371 Seiten)
(371 Seiten)
Software Emulex LP21000 Bedienungsanleitung
(274 Seiten)
(274 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern